Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Palm Coast Homeowners
Water gets into masonry chimneys here quietly. Palm Coast’s heavy summer rain and humid air work on mortar joints, crowns and flashing year after year, and the damage shows up as loose brick, rust streaks or a stain on the ceiling long after the leak started. Our technicians have up to 13 years of experience reading exactly that kind of failure. We inspect first, show you the evidence, then recommend repair. Same-day service is often possible, and estimates are free. Call (877) 471-4123. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a cap over the flue to keep rain, birds and debris out while still letting smoke escape. Every masonry chimney in Palm Coast needs one, and a house with an open flue top is asking for water damage and blocked draft. We install Gelco and Famco caps chosen for the flue size and the venting the appliance needs. Typical pricing runs $250-$650 installed, depending on the cap style and how many flues need covering. Nothing happens until we’ve inspected and shown you what the chimney top looks like.
Why the Cap Matters
An uncapped flue takes rainwater straight down the inside of the chimney, which softens mortar and rusts dampers and liners. A proper cap sheds that water away from the flue and the crown. It also keeps birds and squirrels from nesting where the smoke goes.
Matching the Cap to the Appliance
A wood-burning flue and a gas appliance need different airflow, so the cap style isn’t interchangeable. We pick a Gelco or Famco model that allows the draft the fireplace or insert was designed for. A decorative cap that chokes the draft causes smoke in the room, and that’s a problem we’d rather avoid up front.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the swap-out of a rusted, bent or missing cap that’s no longer doing its job. In Palm Coast, humidity and salt-free but heavy rain still work on cheap steel caps until the mesh tears and the top rusts through. If yours is loose, dented or gone, water and wildlife are getting in. We fit Gelco and Famco replacement caps sized to your existing flue, with pricing typically $250-$650 depending on the model and flue count. We’ll photograph the old cap and the chimney top so you can see why replacement makes sense before we book it.
Spotting a Failing Cap
Rust flakes in the firebox, water stains down the flue, or a cap that shifts in wind all point to replacement. A cap that no longer sits flush lets rain run behind it. If you can see daylight through the mesh, it’s done.
When a Repair Beats Replacement
Sometimes the cap just needs re-securing or a new mesh screen rather than a whole new unit. We check the frame before recommending a full swap. That way you’re not paying for a replacement when a fitting will hold.
Chimney Liner Installation
Chimney Liner Installation is putting a new flue lining inside the chimney so smoke and heat travel safely to the top instead of through cracked masonry. It’s the repair to plan for when a clay tile liner has gaps, or when a new insert or appliance needs a correctly sized flue. This is safety-critical work: a damaged liner lets heat reach framing and lets carbon monoxide into the house, so we only do it as trained professionals. We install DuraFlex liners and use HeatShield resurfacing where the existing liner can be restored instead of replaced. Typical liner work runs $2,800-$6,500 depending on length, appliance and material. HeatShield resurfacing is often less.
Relining vs. Resurfacing
HeatShield lets us repair a liner that’s still structurally sound by resurfacing it rather than tearing it out. When the tiles are cracked through, a full DuraFlex liner is the safer answer. We tell you which applies after a camera inspection.
Sizing for the Appliance
An oversized flue cools smoke too fast and drafts poorly; an undersized one can’t move the volume. We size the liner to the fireplace, insert or gas appliance actually in your home. Getting that right is most of what makes a reline last.
Chimney Flashing Repair
Chimney Flashing Repair is sealing the metal that joins the chimney to the roof so rain can’t slip down the seam between them. Flashing is the most common source of chimney leaks, and in Palm Coast’s rainy season a small gap turns into a ceiling stain fast. We reset or replace the flashing with the right step and counter-flashing for your roof and re-seal the joints properly. Typical flashing repair runs $350-$800 depending on roof type and how much of the flashing must come off. We photograph the leak path so you’re not guessing where the water came from.
Tracing a Leak to the Flashing
Stains that appear near the chimney during heavy rain usually trace back to the flashing seam, not the flue. We check the top and the roof line together. A camera look inside confirms whether water has already reached the attic framing.
Right Material for the Roof
Flashing has to match the roofing and the chimney material or it fails again quickly. We cut and bend the flashing to fit tightly rather than sealing over a gap. A clean install with proper overlap sheds water the way it should.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete slab on top of the chimney that sheds water away from the masonry below it. When the crown cracks or pulls away from the flue, water runs into the brick instead of off it, and that’s the start of most masonry damage we see in Palm Coast. We rebuild or resurface crowns with a proper slope so they drain correctly, and we can tie the repair into a cap install. Typical crown repair runs $400-$1,200 depending on size and whether the crown is patched or rebuilt. We show you the cracks up close before recommending the work.
Why Cracks Spread
A hairline crack in the crown lets water in, and the next hot spell expands it. Left alone, the crack reaches the brick and mortar below. Sealing it early is far cheaper than rebuilding later.
Slope and Overhang
A crown that’s flat or undercut spills water onto the chimney sides instead of away from them. We rebuild with a slope and the right overhang so runoff clears the masonry. That single detail decides how long the repair lasts.
Chimney Repair Companies
Chimney Repair Companies vary a lot in what they can actually do, and it pays to know the difference before you hire. Some sweeps only clean and refer repairs elsewhere; a full-service chimney specialist inspects, sweeps and repairs without sending you to a second contractor. Chimney Sweep Palm Coast handles the whole loop with professional-grade materials: DuraFlex liners, HeatShield resurfacing, Gelco and Famco caps, and components from Olympia Chimney and Copperfield. Typical repair work ranges from a $250-$650 cap to a $2,800-$6,500 reline, all set by a written estimate. We inspect first and show you the evidence.
Questions Worth Asking
Ask whether the company inspects with a camera and shares the footage, and whether it does the repair itself or subcontracts. Ask which materials it uses, not just that it “uses good ones.” A specialist answers those without hesitation.
Reading the Estimate
A written estimate should name the exact repair, the materials and the price, with no vague line items. Watch for a low sweep price that turns into an upsell once someone is on the roof. We put the scope in writing before booking.
Chimney Masonry Repair
Chimney Masonry Repair restores the brick and mortar that hold the chimney together, from repointing joints to rebuilding a section that’s spalled or loose. In Palm Coast, years of humid summers and rain-driven moisture break down mortar until bricks shift, and that’s a structural problem, not just cosmetic. We repoint with mortar matched to the original, replace damaged brick, and use HeatShield for related liner resurfacing where it applies. Typical masonry repair runs $600-$2,500 depending on how much needs rebuilding. We photograph the failing joints so you can see the difference between a touch-up and real repair.
Repointing vs. Rebuilding
When the mortar is crumbling but the brick is sound, repointing restores the wall without a rebuild. When brick faces are spalling or a section is leaning, that part comes down and goes back properly. We tell you which one your chimney actually needs.
Mortar That Fits the Brick
Modern hard mortar against old soft brick traps moisture and cracks the brick over time. We match the mix to the masonry so the repair moves with it. That’s what keeps a repoint from failing in a few seasons.
Brands We Service
We install and service DuraFlex liners and know where a flexible liner wears, kinks or pulls at the top connection over time. We work with HeatShield, the resurfacing system we use to restore a liner instead of replacing it, and we understand where it holds and where it doesn’t. These are the materials certified chimney professionals reach for, and using them is how a repair lasts in this climate.
We fit Gelco and Famco caps for weatherproofing and draft control, and we source components from Olympia Chimney and Copperfield, two of the trade’s most complete supply networks, so uncommon parts aren’t an obstacle here. We service this equipment and know its weak points. Whether you have DuraFlex, HeatShield, Gelco, Famco, Olympia Chimney or Copperfield components, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains or a damp ceiling near the chimney. That usually means flashing or a cracked crown is letting rain in. Left alone, it reaches framing and insulation and the repair grows with it.
- Crumbling mortar or loose brick. If joints are soft or a brick rocks in place, the structure is weakening. A pro should look before a section lets go.
- A strong smoky or creosote smell. That points to a blocked flue or heavy creosote buildup, which raises chimney fire risk. It’s worth a camera inspection to see what’s inside.
- Rust on the damper or firebox. Rust means water is getting in somewhere above. Finding the source early keeps a small fix from becoming a masonry rebuild.
- Smoke rolling back into the room. Poor draft can come from a damaged liner, a blocked flue or a cap that’s too restrictive. It’s a sign to stop using the fireplace until it’s checked.
Our Process, Step by Step
- 1
Book the inspection. We start with a full chimney inspection, including a camera look at the flue, so we can see the actual condition instead of guessing from outside. You get a photo report of what we find, not just a verbal summary.
- 2
Show you the evidence. We walk you through the photos and video so you can see the crack, the gap or the rust for yourself. Nothing is recommended that the footage doesn’t support, and we tell you plainly when a problem can safely wait.
- 3
Set the scope in writing. Once we agree on the repair, you get a written estimate naming the exact work and materials – a DuraFlex liner, HeatShield resurfacing, a Gelco or Famco cap, Olympia Chimney or Copperfield components where needed. The written estimate sets the price.
- 4
Do the repair. We sweep if needed and complete the repair in the same loop, so you’re not coordinating a sweep and a contractor separately. Masonry, crown, flashing and liner work are all handled by the same trade specialists.
- 5
Confirm and close out. We check the finished work and make sure the draft and protection are right before we finish. You keep the photos and the record for your own files.
How Much Does Chimney Repair Cost in Palm Coast?
Chimney repair in Palm Coast depends on which component failed, and the range is wide because a cap is not a reline. A typical cap installation or replacement runs $250-$650 depending on the model and flue count. Flashing repair runs $350-$800 depending on roof type. Crown repair runs $400-$1,200, and masonry repointing or rebuilding runs $600-$2,500 depending on how much needs restoring. Liner work is the largest job: a full DuraFlex liner installation runs $2,800-$6,500, while HeatShield resurfacing of a still-sound liner is often less. All prices are estimates, and the written estimate sets the final price.
What moves the price is how far the damage has spread and which materials the repair needs. A hairline crown crack caught early costs far less than water that’s already reached the framing. We avoid overpaying by inspecting first and fixing only what the evidence supports instead of recommending a full reline you may not need. Your free estimate includes the camera inspection, the photo report and a written scope, so you can compare quotes line by line.
Our Service Area Near Palm Coast
We serve homeowners across Flagler and Volusia counties, including Palm Coast, Flagler Beach, Bunnell, Flagler Estates, Ormond-by-the-Sea, Ormond Beach, Holly Hill, Butler Beach, St. Augustine Shores and St. Augustine Beach. Since we’re specialists serving these areas, we can schedule repairs nearby without sending you to a general contractor. If you’re outside Palm Coast, we can help with chimney repair in Flagler Beach or chimney repair in Bunnell, and our chimney sweep Palm Coast service covers routine cleaning.
Serving Palm Coast, FL – Our Local Coverage Area
We serve Palm Coast and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Palm Coast
Chimney repair is fixing the parts of the chimney that keep smoke in and water out: the liner, cap, flashing, crown and masonry. It’s different from a sweep, which cleans, because repair restores structure and protection. We handle both under one specialist, so a problem found during a sweep can be fixed in the same loop.
Most repairs take from a few hours to a day or two depending on the scope. A cap replacement is quick; a crown rebuild or a full reline takes longer because of the masonry and curing involved. We give you a realistic timeline in the written estimate before we start.
Typical repairs range from $250-$650 for a cap to $2,800-$6,500 for a full liner installation, with flashing, crown and masonry work in between. The written estimate sets the final price after we inspect. Call (877) 471-4123 for an exact quote – estimates are free.
Yes, we install DuraFlex liners and use HeatShield resurfacing, along with Gelco and Famco caps and components from Olympia Chimney and Copperfield. We work with this equipment and know where it wears. Whether you have one of these brands or another make, we can help.
Same-day service is often possible when the schedule allows. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening.
Yes, our work is backed by a satisfaction guarantee, and the materials we install carry the manufacturer’s own coverage. We explain the terms for your specific repair in the written estimate. If something isn’t right after the work, you have a specialist to call back.
Clear the area around the fireplace and hearth and make sure we can reach the roof and the firebox. Move anything breakable away from the work zone and let us know about any gas appliance connected to the chimney. Beyond that, you don’t need to do anything special.
Schedule Your Chimney Repair Service in Palm Coast Today
If your chimney is leaking, crumbling or smoking back, don’t wait for the next storm to make it worse. Call (877) 471-4123 and we’ll inspect first, show you the evidence and quote the repair in writing. Our technicians have up to 13 years of experience, and your no-obligation estimate is free. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Stop by our chimney repair page or call to book a service.
Written by the team at Chimney Sweep Palm Coast.